Plasson valves tech. spec.

PP Mechanical Compression Fittings & Valves

MATERIALS | OPERATING TEMPERATURES CHEMICAL RESISTANCE

OPERATING PRESSURES AND QUALITY CERTIFICATES 

MATERIALS

Compression Fittings
Body: Polypropylene, high-grade copolymer.
Nut: Polypropylene, high-grade copolymer.
Split Ring: Acetal (POM)
Liner: Acetal (POM)
Reinforcing ring: Stainless steel on all female off takes from 1 1/4" up to 4".
Bolts (Series 17): Plated steel.
Nuts (Series 17): Stainless steel.

Valves
Body: Polypropylene, high-grade copolymer. Angle seat valve
O-Ring: See Accessories section
Spring: (items 3067, 3039): Stainless steel.

Saddles
Body: Polypropylene, high-grade copolymer.
Bolts and Nuts: Plated steel.
(Stainless steel bolts and nuts also available)
Reinforcing Rings: Stainless steel.
Seal: Nitrile rubber (NBR).

Tappers + Compression Saddles
Body: Polypropylene, high-grade copolymer.
Split Rings: Acetal (POM).
Nuts: Polypropylene, high-grade copolymer.
Bolts and Nuts: Stainless Steel.
Seal: EPDM

Threaded Fittings
Body: Polypropylene, high-grade copolymer.
Reinforcing Ring: Stainless Steel.

CHEMICAL RESISTANCE
Plasson Fittings are supplied, as standard, with Polyacetal split rings and NBR O-rings which are suitable for water.
 For aggressive chemical applications CPVC split rings and EPDM or FPM O-rings can be supplied to produce a better chemical resistance.

THREADS

All threads conform to ISO-7; BS 21 - 1973; DIN 2999; NEN 3258; AS 1722 Part 1 - 1975.
External taper threads all sizes.
Internal parallel thread up to 2 1/2"; internal taper thread 3 " and up.

FLANGES

Flange dimensions in accordance with: ISO 7005-1 (TABLE 11), BS 4504:1989, DIN 2501, AS/NZS 4331.
Metal backing rings to be used with all flanges.

Legend

Unless otherwise indicated, all dimensions are in mm
A,A1,L - Length from centerline to end of fitting
B,D,D1 - Diameter
Dp - Pitch circle diameter of bolt holes in flanges
d,d1 - Nominal diameter of fitting corresponding
to outside pipe diameter
e - Cross section diameter of O-ring
E,E1 - Overall diameter of compression fitting
G,G1 -Nominal size of thread (inches)
H - Overall length of fitting
l,l1 - Length of portion of the pipe inside the fitting
l2 - Length of thread
S - Bolt hole diameter in flange
t - Thickness of metal flange
W - Weight in grams
n- Number of bolt holes in flanges

NOTE:

Catalogue numbers of Series 7 fittings supplied with grey nut have final digit "0" . Those supplied with black nut have final digit "6"  For the sake of simplification, final digit "0" is used throughout this catalogue.

OPERATING PRESSURES AND QUALITY CERTIFICATES

Plasson compression fittings have been tested and approved by major standard institutions such as: WRAS (GB), KIWA (NL), Standards Institution of Israel (IL), QAS (AUS), Statens Provingsanstalt Stockholm (S), Statens Planmerk (S), SVGW (CH), Byggestyrelsen (DK), SKZ (analogous to DIN 8076 Part 3) (D), IIP (UNI 9561) (IT).

For Example:IIP (UNI 9561

PN 16- 16mm -110mm diameter
PN 10- 125mm -160mm diameter

AS/NZS 4129 -2000
PN 16-16mm - 63mm diameter
PN 12.5-75mm - 160mm diameter

PN 6 for all 4" female threads

Plasson's Quality Assurance System is:
ISO-9002 certified

valves for